IHIConnectors

Accepted forms of payment:

Through Hole Technology PCB Wire Terminals

IHI High current PCB terminal lugs - maximum currents from
20 to 285 AMPs maximum wire capacity fromAWG #12 to 300 kcmil /MCM

Dimensions

A: 0.31" (7.9mm)

B: 0.46" (11.7mm)

C: 0.26" (6.6mm)

See Mechanical Drawing for detailed dimensions

*Wire range only valid with use of a bus bar or staple.

"B12" 12 AWG OEM, 12-16 AWG wire range, tin plated aluminum, single wire, copper wire only, CU7, 75C temperature rating, UL Recognized at 600v - acceptable for use through 2000v.

Please email for higher volume prices

Temperature Range and Rating Guide

Dimensions

A: 0.31" (7.9mm)

B: 0.46" (11.7mm)

C: 0.26" (6.6mm)

See Mechanical Drawing for detailed dimensions

B12-PCB-S: 12 AWG PCB wire lug, 12-16* AWG, 20 AMP, slotted head screw. 2 LEGS at .14X.063” cross section and 0.12” (3.0mm) penetration PCB penetration. Side wire, and top screw entrance. UL Recognized at 600v - acceptable for use through 2000v, Made in the USA from domestic and imported parts.

Temperature Range and Rating Guide

Body and Staple THT Types

 Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper wire, stranded and solid wire per UL486 wire code. Solid copper bus staple for tens of micro ohms range of copper to copper high conductivity, low resistance current path.  Meets IEC volt drop test standards. 

*16 AWG or fine stranded wires recommend to use wire ferrules.

Zinc plated steel screw, and tin plated copper staple

Dimensions

A: 0.31" (7.9mm)

B: 0.46" (11.7mm)

C: 0.26" (6.6mm)

See Mechanical Drawing for detailed dimensions

B12-PCB-NM-HEX: 10 AWG PCB wire lug, 10-14,16* AWG, 20 AMP, Hex socket screw. 2 LEGS at .14X.063” cross section and 0.12” (3.0mm) penetration PCB penetration. Side wire, and top screw entrance. No markings on body.

*16 AWG or fine stranded wires recommend to use wire ferrules.

Temperature Range and Rating Guide

Body and Staple THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper wire, stranded and solid wire per UL486 wire code. Solid copper bus staple for tens of micro ohms range of copper to copper high conductivity, low resistance current path. Meets IEC volt drop test standards. 

Zinc plated steel screw, and tin plated copper staple

Dimensions

A: 0.31" (7.9mm)

B: 0.46" (11.7mm)

C: 0.26" (6.6mm)

See Mechanical Drawing for detailed dimensions

B12-PCB-NM24-HEX: 10 AWG, 20 AMP, Hex socket screw, 10-14,16* AWG wire range. 2 LEGS at .14X.063” cross section and 0.23” (5.8mm) penetration PCB penetration. Side wire, and top screw entrance. No markings on body. Zinc plated steel screw, tin plated copper staple. International Hydraulics inc.

*16 AWG or fine stranded wires recommend to use wire ferrules.

Temperature Range and Rating Guide

Body and Staple THT Types

 Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper wire, stranded and solid wire per UL486 wire code. Solid copper bus staple for tens of micro ohms range of copper to copper high conductivity, low resistance current path.  Meets IEC volt drop test standards. 

Zinc plated steel screw, and tin plated copper staple

Dimensions

A: 0.34" (8.6mm)

B: 0.49" (12.4mm)

C: 0.26" (6.6mm)

D: 0.39" (9.9mm)

See Mechanical Drawing for detailed dimensions

B10-PCB: 10 AWG PCB wire lug, 10-16* AWG, 30 AMP, slotted head screw. 1 leg at .336X.14” with a .10" (2.54mm) PCB penetration. Side wire, and top screw entrance.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper or aluminum wire, stranded and solid wire per UL486 wire code. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards. Variety of wire binding screw options.

Soldering Recommendations

*16 AWG or fine stranded wires recommend to use wire ferrules.

Zinc plated steel screw,and integrated aluminum foot, tin plated, solderable

Dimensions

A: 0.34" (8.6mm)

B: 0.49" (12.4mm)

C: 0.26" (6.6mm)

D: 0.39" (9.9mm)

See Mechanical Drawing for detailed dimensions

B10-PCB-HEX: 10 AWG PCB wire lug, 10-16* AWG, 30 AMP, Hex socket screw. 1 leg at .336X.14” with a .10" (2.54mm) PCB penetration. Side wire, and top screw entrance.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper or aluminum wire, stranded and solid wire per UL486 wire code. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards. Variety of wire binding screw options.

Soldering Recommendations

*16 AWG or fine stranded wires recommend to use wire ferrules.

Zinc plated steel screw, and integrated aluminum foot, tin plated, solderable

When tightening bolt,
two wrenches should be used to avoid damaging smt bond

Dimensions

A: 0.34" (8.6mm)

B: 0.49" (12.4mm)

C: 0.26" (6.6mm)

D: 0.39" (9.9mm)

See Mechanical Drawing for detailed dimensions

B10-PCB-RLM-KIT: Ring lug mount block with integrated aluminum foot, tin plated, solderable. 1 leg at .336X.14” with a .10" (2.54mm) PCB penetration. Suggested ring lug wire sizes 10-16 AWG, up to 30 Amps. Kitted with a zinc plated steel phillips screw and washer. Ring lug mount and top bolt entrance. Part side hole not intended for wire insertion when the part is used as a ring lug mount. When tightening bolt, two wrenches should be used to avoid damaging solder bond. International Hydraulics Inc.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Wire choice affected by customer supplied ring lug and ring lug codes and ratings. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards.

Soldering Recommendations

65A  with 6AWG copper wire (purchase 2 RLM connectors, 1 crimp lug is purchased by customer)

Ring lug not included.

When tightening bolt,
two wrenches should be used to avoid damaging smt bond

Dimensions

A: 0.34" (8.6mm)

B: 0.49" (12.4mm)

C: 0.26" (6.6mm)

D: 0.39" (9.9mm)

See Mechanical Drawing for detailed dimensions

B10-PCB-RLM-G-KIT:Ring lug mount block with integrated aluminum foot, tin plated, solderable. 1 leg at .336X.14” with a .10"(2.54mm) PCB penetration. Suggested ring lug wire sizes 10-16 AWG, up to 30 Amps. Kitted with a green phillips/slotted combo grounding screw. Not UL467 KDER. For use with ring lug. Not intended for wire insertion except with bare, #10 AWG, solid grounding wire. Part side hole not intended for wire insertion when the part is used as a ring lug mount. Ring lug mount and top bolt entrance. For use with ring lug. Not intended for wire insertion except with bare, #10 AWG, solid grounding wire. International Hydraulics inc.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper or aluminum wire, stranded and solid wire per UL486 wire code. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards.

Soldering Recommendations

*16 AWG or fine stranded wires recommend to use wire ferrules.

Zinc plated steel screw, and integrated aluminum foot, tin plated, solderable

Surface Mount Application | #10 AWG Solid, Grounding Wire Application | Ring lug not included

Dimensions

A: 0.34" (8.6mm)

B: 0.49" (12.4mm)

C: 0.26" (6.6mm)

D: 0.39" (9.9mm)

See Mechanical Drawing for detailed dimensions

B10-PCB-NS: 10 AWG, 30 AMP,10-16* AWG wire range. Sold less the wire binding screws so clients can provide their own #10-32 screw. 1 leg with a .336X.14” penetration. Side wire entrance, no screw. Integrated aluminum foot, tin plated bus.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper or aluminum wire, stranded and solid wire per UL486 wire code. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards. Variety of wire binding screw options.

Soldering Recommendations

*16 AWG or fine stranded wires recommend to use wire ferrules.

Zinc plated steel screw,and integrated aluminum foot, tin plated, solderable

Dimensions

A: 0.34" (8.6mm)

B: 0.52" (13.2mm)

C: 0.34" (8.6mm)

D: 0.42" (10.7mm)

See Mechanical Drawing for detailed dimensions

B6A-PCB: 6 AWG PCB wire lug, 6-16* AWG, 65 AMP, slotted set screw. 1 leg at .336X.14” with a .10" (2.54mm) PCB penetration. Side wire, and top screw entrance.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper or aluminum wire, stranded and solid wire per UL486 wire code. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards. Variety of wire binding screw options.

Screwdriver Bit Information

Soldering Recommendations

*16 AWG or fine stranded wires recommend to use wire ferrules.

Zinc plated steel screw, and integrated aluminum foot, tin plated, solderable

Dimensions

A: 0.34" (8.6mm)

B: 0.52" (13.2mm)

C: 0.34" (8.6mm)

D: 0.42" (10.7mm)

See Mechanical Drawing for detailed dimensions

B6A-PCB-SS is End Of Life status with limited long term parts supply, see replacement part B6A-PCB with zinc plated steel screw.

Current stock 70,000 pcs (4/2024)

Lead time for 5k 2 weeks from PO for assembly

Lead time for large quantities 2 weeks plus 1 week per 10k pcs for assembly

B6A-PCB-SS: 6 AWG PCB wire lug, 6-16* AWG, 65 AMP, slotted set screw. 1 leg at .336X.14” with a .10" (2.54mm) PCB penetration. Side wire, and top screw entrance.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper or aluminum wire, stranded and solid wire per UL486 wire code. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards. Variety of wire binding screw options.

Soldering Recommendations

*16 AWG or fine stranded wires recommend to use wire ferrules.

Stainless Steel screw, and integrated aluminum foot, tin plated, solderable

Dimensions

A: 0.34" (8.6mm)

B: 0.52" (13.2mm)

C: 0.34" (8.6mm)

D: 0.42" (10.7mm)

See Mechanical Drawing for detailed dimensions

B6A-PCB-HEX: 6 AWG PCB wire lug, 6-16* AWG, 65 AMP, HEX socket set screw. 1 leg at .336X.14”with a .10" (2.54mm) PCB penetration. Side wire, and top screw entrance, 1/8” or (option) 3mm HEX socket set screw.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper or aluminum wire, stranded and solid wire per UL486 wire code. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards. Variety of wire binding screw options.

Soldering Recommendations

*16 AWG or fine stranded wires recommend to use wire ferrules.

Zinc plated steel screw, and integrated aluminum foot, tin plated, solderable

Dimensions

A: 0.34" (8.6mm)

B: 0.52" (13.2mm)

C: 0.34" (8.6mm)

D: 0.42" (10.7mm)

See Mechanical Drawing for detailed dimensions

Note!!!   This part has a 3mm hex socket for use in metric countries.

B6A-PCB-HEX-M: 6 AWG PCB wire lug, 6-16* AWG, 65 AMP, Metric Hex socket set screw. 1 leg at .336X.14”with a .10" (2.54mm) PCB penetration. Side wire, and top screw entrance, 1/8” or (option) 3mm HEX socket set screw.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper or aluminum wire, stranded and solid wire per UL486 wire code. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards. Variety of wire binding screw options.

Soldering Recommendations

*16 AWG or fine stranded wires recommend to use wire ferrules.

Zinc plated steel screw, and integrated aluminum foot, tin plated, solderable

Dimensions

A: 0.34" (8.6mm)

B: 0.52" (13.2mm)

C: 0.34" (8.6mm)

D: 0.42" (10.7mm)

See Mechanical Drawing for detailed dimensions

B6A-PCB-RS: 6 AWG PCB wire lug, 6-16* AWG, 65 AMP, Slotted & Robertson Recess Head screw. 1 leg at .336X.14” with a .10" (2.54mm) PCB penetration. Side wire, and top screw entrance.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper or aluminum wire, stranded and solid wire per UL486 wire code. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards. Variety of wire binding screw options.

Soldering Recommendations

*16 AWG or fine stranded wires recommend to use wire ferrules.

Zinc plated steel screw, and integrated aluminum foot, tin plated, solderable

Dimensions

A: 0.34" (8.6mm)

B: 0.52" (13.2mm)

C: 0.34" (8.6mm)

D: 0.42" (10.7mm)

See Mechanical Drawing for detailed dimensions

B6A-PCB-RS-NS: 6 AWG PCB wire lug, 6-14 AWG, 65 AMP, 1 leg at .336X.14” with a .10" (2.54mm) PCB penetration. Side wire and top screw entrance.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper or aluminum wire, stranded and solid wire per UL486 wire code. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards. Variety of wire binding screw options.

Soldering Recommendations

Dimensions

A: 0.34" (8.6mm)

B: 0.57" (14.5mm)

C: 0.34" (8.6mm)

D: 0.44" (11.2mm)

See Mechanical Drawing for detailed dimensions

B6A-NH-PCB-RS-NS: 6 AWG PCB wire lug, 6-14 AWG, 65 AMP, 1 leg at .336X.14” with a .13" (3.30mm) PCB penetration. Top screw entrance.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper or aluminum wire, stranded and solid wire per UL486 wire code. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards. Variety of wire binding screw options.

Soldering Recommendations

Image 1 and 2 THT B6A-NH-PCB-RS-NS. Image 3 "Marine Version" 2RLM with B6A-NH-PCB-RS-NS and customer supplied standard commercial stainless hardware

Ring Lugs not included.

Dimensions

A: 0.34" (8.6mm)

B: 0.57" (14.5mm)

C: 0.34" (8.6mm)

D: 0.44" (11.2mm)

See Mechanical Drawing for detailed dimensions

B6A-NH-PCB-RLM KIT: Ring lug mount block with integrated aluminum foot, tin plated, solderable. 1 leg at .336X.14” with a .13" (3.30mm) PCB penetration. Suggested ring lug wire sizes 6-14 AWG, up to 65 AMP. Kitted with a zinc plated steel 1/4-28 hex cap bolt and 5/8" outer diameter washer. Ring lug mount and top bolt entrance. Ring lug not included. When tightening bolt, two wrenches should be used to avoid damaging solder bond. Suitable for potting applications depending on mounting direction. International Hydraulics Inc® brand.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Wire choice affected by customer supplied ring lug and ring lug codes and ratings. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards.

Soldering Recommendations

When tightening bolt, two wrenches should be used to avoid damaging solder bond

Ring Lugs not included.

Dimensions

A: 0.34" (8.6mm)

B: 0.57" (14.5mm)

C: 0.34" (8.6mm)

D: 0.44" (11.2mm)

See Mechanical Drawing for detailed dimensions

B6A-NH-PCB-RLM-12W KIT: Ring lug mount block with integrated aluminum foot, tin plated, solderable. 1 leg at .336X.14” with a .13" (3.30mm) PCB penetration. Suggested ring lug wire sizes 6-14 AWG, up to 65 AMP. Kitted with a zinc plated steel 1/4-28 hex cap bolt and M6 washer. Ring lug mount and top bolt entrance. Ring lug not included. When tightening bolt, two wrenches should be used to avoid damaging solder bond. Suitable for potting applications depending on mounting direction. International Hydraulics Inc® brand.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Wire choice affected by customer supplied ring lug and ring lug codes and ratings. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards.

Soldering Recommendations

When tightening bolt, two wrenches should be used to avoid damaging solder bond

Ring lug not included

Part not assembled

When tightening bolt,
two wrenches should be used to avoid damaging solder bond

B6A-PCB-RLM KIT: Ring lug mount block with integrated aluminum foot, tin plated, solderable. 1 leg at .336X.14” with a .10" (2.54mm) PCB penetration. Suggested ring lug wire sizes 6-16 AWG, up to 65 AMP. Kitted with a zinc plated steel 1/4-28 hex cap bolt and washer. Ring lug mount and top bolt entrance. Part side hole not intended for wire insertion when the part is used as a ring lug mount. When tightening bolt, two wrenches should be used to avoid damaging solder bond. International Hydraulics Inc® brand.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper or aluminum wire, stranded and solid wire per UL486 wire code. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards.

Soldering Recommendations

When tightening bolt, two wrenches should be used to avoid damaging solder bond.

When tightening bolt,
two wrenches should be used to avoid damaging solder bond

B6A-PCB-RLM-12W KIT: Ring lug mount block with integrated aluminum foot, tin plated, solderable. 1 leg at .336X.14” with a .10" (2.54mm) PCB penetration. Suggested ring lug wire sizes 6-16 AWG, up to 65 AMP. Kitted with a zinc plated steel 1/4-28 hex cap bolt and M6 washer. Ring lug mount and top bolt entrance. Part side hole not intended for wire insertion when the part is used as a ring lug mount. When tightening bolt, two wrenches should be used to avoid damaging solder bond. International Hydraulics Inc® brand.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Wire choice affected by customer supplied ring lug and ring lug codes and ratings. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards.

Soldering Recommendations

Ring lugs not included

Part not assembled

When tightening bolt, two wrenches should be used to avoid damaging solder bond

Dimensions

A: 0.34" (8.6mm)

B: 0.52" (13.2mm)

C: 0.34" (8.6mm)

D: 0.42" (10.7mm)

See Mechanical Drawing for detailed dimensions

B6A-PCB-2RLM KIT: Double Ring lug mount block with integrated aluminum foot, tin plated, solderable. 1 leg at .336X.14” with a .10" (2.54mm) PCB penetration. Suggested ring lug wire sizes 6-16 AWG, up to 65 AMP. Kitted with a zinc plated steel 1/4-28 hex socket screw and split ring washer. Ring lugs not included. Able to fit 2 ring lugs. Part side hole not intended for wire insertion when the part is used as a ring lug mount. SMT/SMD solderable tin plated. Interntaional Hydraulics Inc. brand.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Wire choice affected by customer supplied ring lug and ring lug codes and ratings. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards.

Soldering Recommendations

Dimensions

A: 0.53" (13.5mm)

B: 0.50" (12.7mm)

C: 0.34" (8.6mm)

See Mechanical Drawing for detailed dimensions

B6A-PCB-45: 6 AWG PCB wire lug, 6-16* AWG, 65 AMP, slotted screw, 1 leg at .336X.14” with a .125" (3.18mm) PCB penetration. Top wire, and screw entrance at 45 degrees.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper or aluminum wire, stranded and solid wire per UL486 wire code. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards. Variety of wire binding screw options.

Screwdriver Bit Information

Soldering Recommendations

*16 AWG or fine stranded wires recommend to use wire ferrules.

Zinc plated steel screw, and integrated aluminum foot, tin plated, solderable

Dimensions

A: 0.53" (13.5mm)

B: 0.50" (12.7mm)

C: 0.34" (8.6mm)

See Mechanical Drawing for detailed dimensions

B6A-PCB-45-HEX: 6 AWG PCB wire lug, 6-16* AWG, 65 AMP, HEX socket screw, 1 leg at .336X.14” with a .125" (3.18mm) PCB penetration. Top wire, and screw entrance at 45 degrees.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper or aluminum wire, stranded and solid wire per UL486 wire code. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards. Variety of wire binding screw options.

Soldering Recommendations

*16 AWG or fine stranded wires recommend to use wire ferrules.

Zinc plated steel screw, and integrated aluminum foot, tin plated, solderable

Dimensions

A: 0.53" (13.5mm)

B: 0.50" (12.7mm)

C: 0.34" (8.6mm)

See Mechanical Drawing for detailed dimensions

B6A-PCB-45-HEX-M: 6 AWG PCB wire lug, 6-16* AWG, 65 AMP, HEX socket screw, 1 leg at .336X.14” with a .125" (3.18mm) PCB penetration. Top wire, and screw entrance at 45 degrees.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper or aluminum wire, stranded and solid wire per UL486 wire code. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards. Variety of wire binding screw options.

Soldering Recommendations

*16 AWG or fine stranded wires recommend to use wire ferrules.

Zinc plated steel screw, and integrated aluminum foot, tin plated, solderable

Dimensions

A: 0.53" (13.5mm)

B: 0.50" (12.7mm)

C: 0.34" (8.6mm)

See Mechanical Drawing for detailed dimensions

B6A-PCB-45-RS: 6 AWG PCB wire lug, 6-16* AWG, 65 AMP, slotted robertson recess screw, 1 leg at .336X.14” with a .125" (3.18mm) PCB penetration. Top wire, and screw entrance at 45 degrees.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper or aluminum wire, stranded and solid wire per UL486 wire code. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards. Variety of wire binding screw options.

Soldering Recommendations

*16 AWG or fine stranded wires recommend to use wire ferrules.

Zinc plated steel screw, and integrated aluminum foot, tin plated, solderable

Dimensions

A: 0.53" (13.5mm)

B: 0.50" (12.7mm)

C: 0.34" (8.6mm)

See Mechanical Drawing for detailed dimensions

B6A-PCB-45-RLM-12W-KIT: Ring lug mount block with integrated aluminum foot, tin plated, solderable. 1 LEG at .336X.14” (8.5X3.5mm) 0.10" 2.54mm PCB penetration. Suggested ring lug wire sizes 6-16 AWG, up to 65 AMP. Kitted with a zinc plated steel 1/4-28 hex cap bolt and M6 washer. Ring lug mount and top bolt entrance. Part side hole not intended for wire insertion when the part is used as a ring lug mount. When tightening bolt, two wrenches should be used to avoid damaging solder bond. International Hydraulics Inc® brand.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Wire choice affected by customer supplied ring lug and ring lug codes and ratings. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards. Variety of wire binding screw options.

Soldering Recommendations

When tightening bolt, two wrenches should be used to avoid damaging solder bond.

Dimensions

A: 0.38" (9.5mm)

B: 0.53" (13.5mm)

C: 0.38" (9.7mm)

See Mechanical Drawing for detailed dimensions

B6B-PCB: 6 AWG PCB wire lug, 6-14 AWG, 65 AMP, slotted set screw. 2 legs (.20X.05”) with a 0.15" (3.8mm) PCB penetration. Side wire, and top screw entrance. International Hydraulics Inc® brand.

Screwdriver Bit Information

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper or aluminum wire, stranded and solid wire per UL486 wire code. Solid copper bus staple for tens of micro ohms range of copper to copper high conductivity, low resistance current path. Meets IEC volt drop test standards. Variety of THT leg length to accommodate PCB of various thicknesses including multilayer.

Zinc plated steel screw, and tin plated copper staple, solderable

Dimensions

A: 0.38" (9.7mm)

B: 0.62" (15.7mm)

C: 0.38" (9.7mm)

D: 0.49" (12.4mm)

See Mechanical Drawing for detailed dimensions

B4A-PCB: 4 AWG PCB wire lug, 4-14 AWG, 85 AMP, slotted screw. 1 leg at .375X.14”with a .13" (3.3mm) PCB penetration. Side wire, and top screw entrance, slotted screw. IHI Connectors® brand.

Screwdriver Bit Information

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper or aluminum wire, stranded and solid wire per UL486 wire code. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards. Variety of wire binding screw options.

Soldering Recommendations

Zinc plated steel screw, and integrated aluminum foot, tin plated, solderable

Dimensions

A: 0.38" (9.7mm)

B: 0.62" (15.7mm)

C: 0.38" (9.7mm)

D: 0.49" (12.4mm)

See Mechanical Drawing for detailed dimensions

B4A-PCB-HEX: 4 AWG PCB wire lug, 4-14 AWG, 85 AMP, HEX socket set screw. 1 leg at .375X.14”with a .13" (3.3mm) PCB penetration. Side wire, and top screw entrance, 1/8” HEX socket set screw. IHI Connectors® brand.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper or aluminum wire, stranded and solid wire per UL486 wire code. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards. Variety of wire binding screw options.

Soldering Recommendations

Zinc plated steel screw, and integrated aluminum foot, tin plated, solderable

Dimensions

A: 0.38" (9.7mm)

B: 0.62" (15.7mm)

C: 0.38" (9.7mm)

D: 0.49" (12.4mm)

See Mechanical Drawing for detailed dimensions

B4A-PCB-HEX-M: 4 AWG PCB wire lug, 4-14 AWG, 85 AMP, Metric HEX socket set screw. 1 leg at .375X.14”with a .13" (3.3mm) PCB penetration. Side wire, and top screw entrance, 3mm HEX socket set screw. IHI Connectors® brand.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper or aluminum wire, stranded and solid wire per UL486 wire code. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards. Variety of wire binding screw options.

Soldering Recommendations

Zinc plated steel screw, and integrated aluminum foot, tin plated, solderable

Dimensions

A: 0.38" (9.7mm)

B: 0.62" (15.7mm)

C: 0.38" (9.7mm)

D: 0.49" (12.4mm)

See Mechanical Drawing for detailed dimensions

B4A-PCB-RS: 4 AWG PCB wire lug, 4-14 AWG, 85 AMP, slotted robertson recess head screw. 1 leg at .375X.14” with a .13" (3.3mm) PCB penetration. Side wire, and top screw entrance, slotted robertson recess head screw. International Hydraulics Inc® brand.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper or aluminum wire, stranded and solid wire per UL486 wire code. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards. Variety of wire binding screw options.

Soldering Recommendations

Zinc plated steel screw, and integrated aluminum foot, tin plated, solderable

Ring lug not included

Part not assembled

Dimensions

A: 0.38" (9.7mm)

B: 0.62" (15.7mm)

C: 0.38" (9.7mm)

D: 0.49" (12.4mm)

See Mechanical Drawing for detailed dimensions

B4A-PCB-RLM-KIT: Ring lug mount block with integrated aluminum foot, tin plated, solderable. 1 LEG at .375X.14” (9.53X3.5mm) 0.13" 3.3mm PCB penetration Suggested ring lug wire sizes 4-14 AWG, up to 85 Amps. Kitted with a zinc plated steel 1/4-28 hex cap bolt and washer. Ring lug mount and top bolt entrance. Part side hole not intended for wire insertion when the part is used as a ring lug mount. When tightening bolt, two wrenches should be used to avoid damaging solder bond. International Hydraulics Inc® brand.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Wire choice affected by customer supplied ring lug and ring lug codes and ratings. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards.

Soldering Recommendations

130A with 1/0 AWG copper wire (purchase 2 RLM connectors, 1 crimp lug is purchased by customer)

When tightening bolt, two wrenches should be used to avoid damaging solder bond.

Dimensions

A: 0.38" (9.7mm)

B: 0.62" (15.7mm)

C: 0.38" (9.7mm)

D: 0.49" (12.4mm)

See Mechanical Drawing for detailed dimensions

B4A-PCB-RLM-12W KIT: Ring lug mount block with integrated aluminum foot, tin plated, solderable. 1 LEG at .375X.14” (9.53X3.5mm) 0.13" 3.3mm PCB penetration Suggested ring lug wire sizes 4-14 AWG, up to 85 Amps. Kitted with a zinc plated steel 1/4-28 hex cap bolt and M6 washer. Ring lug mount and top bolt entrance. Part side hole not intended for wire insertion when the part is used as a ring lug mount. When tightening bolt, two wrenches should be used to avoid damaging solder bond. International Hydraulics Inc® brand.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Wire choice affected by customer supplied ring lug and ring lug codes and ratings. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards.

Soldering Recommendations

130A with 1/0 AWG copper wire (purchase 2 RLM connectors, 1 crimp lug is purchased by customer)

Ring lugs not included

Part not assembled

When tightening bolt, two wrenches should be used to avoid damaging solder bond

Dimensions

A: 0.38" (9.7mm)

B: 0.62" (15.7mm)

C: 0.38" (9.7mm)

D: 0.49" (12.4mm)

See Mechanical Drawing for detailed dimensions

B4A-PCB-2RLM-KIT: Double Ring lug mount block with integrated aluminum foot, tin plated, solderable. 1 leg at .375X.14” with a .13" (3.3mm) PCB penetration. Kitted with a zinc plated steel 1/4-28 hex socket screw and split ring washer. Ring lugs not included. Able to fit 2 ring lugs. Part side hole not intended for wire insertion when the part is used as a ring lug mount. SMT/SMD solderable tin plated. Interntaional Hydraulics Inc. brand.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Wire choice affected by customer supplied ring lug and ring lug codes and ratings. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards.

Soldering Recommendations

130A with (2) 1/0 AWG copper wires (purchase (2) 2RLM connectors, 2 crimp lug is purchased by customer)

Dimensions

A: 0.38" (9.7mm)

B: 0.62" (15.7mm)

C: 0.38" (9.7mm)

D: 0.49" (12.4mm)

See Mechanical Drawing for detailed dimensions

B4A-PCB-NS: 4 AWG PCB wire lug, 4-14 AWG, 85 AMP, no screw. 1 leg at .375X.14” with a .13" (3.3mm) PCB penetration. Side wire, and top screw entrance, no screw. IHI Connectors® brand.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper or aluminum wire, stranded and solid wire per UL486 wire code. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards. Variety of wire binding screw options.

Soldering Recommendations

No screw, and integrated aluminum foot, tin plated, solderable

Dimensions

A: 0.53" (13.5mm)

B: 0.50" (12.7mm)

C: 0.38" (9.7mm)

See Mechanical Drawing for detailed dimensions

B4A-PCB-45: 4 AWG PCB wire lug, 4-16* AWG, 85 AMP, slotted set screw, 1 leg at .375x.14” with a .125" (3.18mm) PCB penetration. Top wire, and screw entrance at 45 degrees.

Screwdriver Bit Information

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper or aluminum wire, stranded and solid wire per UL486 wire code. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards. Variety of wire binding screw options.

Soldering Recommendations

*16 AWG or fine stranded wires recommend to use wire ferrules.

Zinc plated steel screw, and integrated aluminum foot, tin plated, solderable

Dimensions

A: 0.53" (13.5mm)

B: 0.50" (12.7mm)

C: 0.38" (9.7mm)

See Mechanical Drawing for detailed dimensions

B4A-PCB-45-HEX: 4 AWG PCB wire lug, 4-16* AWG, 85 AMP, Hex socket screw, 1 leg at .375x.14” with a .125" (3.18mm) PCB penetration. Top wire, and screw entrance at 45 degrees.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper or aluminum wire, stranded and solid wire per UL486 wire code. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards. Variety of wire binding screw options.

Soldering Recommendations

*16 AWG or fine stranded wires recommend to use wire ferrules.

Zinc plated steel screw, and integrated aluminum foot, tin plated, solderable

Dimensions

A: 0.53" (13.5mm)

B: 0.50" (12.7mm)

C: 0.38" (9.7mm)

See Mechanical Drawing for detailed dimensions

B4A-PCB-45-RS: 4 AWG PCB wire lug, 4-16* AWG, 85 AMP, Slotted robertson recess screw, 1 leg at .375x.14” with a .125" (3.18mm) PCB penetration. Top wire, and screw entrance at 45 degrees.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper or aluminum wire, stranded and solid wire per UL486 wire code. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards. Variety of wire binding screw options.

Soldering Recommendations

*16 AWG or fine stranded wires recommend to use wire ferrules.

Zinc plated steel screw, and integrated aluminum foot, tin plated, solderable

Ring Lugs not included.

When tightening bolt, two wrenches should be used to avoid damaging solder bond

Dimensions

A: 0.53" (13.5mm)

B: 0.50" (12.7mm)

C: 0.38" (9.7mm)

See Mechanical Drawing for detailed dimensions

B4A-PCB-45-RLM-KIT: Ring lug mount block with integrated aluminum foot, tin plated, solderable. Suggested ring lug wire sizes 4-18 AWG, up to 85 Amps. 1 leg at .375X.14” with a .125" (3.18mm) PCB penetration. SMT/SMD solderable tin plated. When tightening bolt, two wrenches should be used to avoid damaging solder bond. Ring lug not included. Suitable for potting applications depending on mounting direction. International Hydraulics Inc® brand.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Wire choice affected by customer supplied ring lug and ring lug codes and ratings. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards. Variety of wire binding screw options.

Soldering Recommendations

115A  with 2AWG copper wire (purchase 2 RLM connectors, 1 crimp lug is purchased by customer)

150A with 1/0 copper wire (purchase 2 RLM connectors, 1 crimp lug is purchased by customer)

195A with 2/0 copper wire (purchase 2 RLM connectors, 1 crimp lug is purchased by customer)

Ring Lugs not included.

When tightening bolt, two wrenches should be used to avoid damaging solder bond

Dimensions

A: 0.53" (13.5mm)

B: 0.50" (12.7mm)

C: 0.38" (9.7mm)

See Mechanical Drawing for detailed dimensions

B4A-PCB-45-RLM-12W KIT: Ring lug mount block with integrated aluminum foot, tin plated, solderable. Suggested ring lug wire sizes 4-18 AWG, up to 85 Amps. 1 leg at .375X.14” with a .125" (3.18mm) PCB penetration. Kitted with a zinc plated steel 1/4-28 hex cap bolt and M6 washer. Ring lug not included. International Hydraulics Inc® brand.

Temperature Range and Rating Guide

One piece Body THT Types

Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Wire choice affected by customer supplied ring lug and ring lug codes and ratings. Solid mass, high conductivity aluminum alloy body for tens of micro ohms range of resistance wire to foil conductivity, low resistance current path. Meets IEC volt drop test standards.

Soldering Recommendations

115A  with 2AWG copper wire (purchase 2 RLM connectors, 1 crimp lug is purchased by customer)

150A with 1/0 copper wire (purchase 2 RLM connectors, 1 crimp lug is purchased by customer)

195A with 2/0 copper wire (purchase 2 RLM connectors, 1 crimp lug is purchased by customer)

Dimensions

A: 0.47" (11.9mm)

B: 0.55" (14.0mm)

C: 0.46" (11.7mm)

See Mechanical Drawing for detailed dimensions

*Wire range only valid with use of a bus bar or staple.

For mounting and anti rotation methods see the IHI B4B Installation Guide.

B4B has been updated with UL Listing in addition to Canada certification.

"B4B-B" 4 AWG OEM, 4-14 AWG wire range, single wire, all copper body, solid brass screw, copper wire only, CU9, 90C temperature rating, Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application, and Canada Certified for USA and Canada, good for heavy duty applications and environments and "copper only" codes, oversized wire opening. Flat end screw with cut trepan face for gripping large and small stranded wires without damage. 0.20" Dia. plain mounting hole (#10 screw) (may be tapped 1/4-28 by user and permitted in file) or bus "keeper" hole. 95 AMPs, Bus .25 x .063 copper alloy minimum cross section. Mounting hole .20 dia. (may be tapped 1/4-28 by user and permitted in file). International Hydraulics Inc® brand.

E129884 UL486A,B, ZMVV, ZMVV7, 1243943 Canada 22.2 No.65

Temperature Range and Rating Guide

Please email for higher volume prices

Dimensions

A: 0.47" (11.9mm)

B: 0.55" (14.0mm)

C: 0.46" (11.7mm)

See Mechanical Drawing for detailed dimensions

For mounting and anti rotation methods see the IHI B4B Installation Guide.

B4B has been updated with UL Listing in addition to Canada certification.

"B4B-PCB-B" 4 AW, 95 AMP, 4-14 AWG wire range, single wire, all copper body, solid brass screw, copper wire only, CU9, 90C temperature rating, Voltage Rating: 600 V, 2000 V or to 35 KV (uninsulated) depending on application, and Canada Certified for USA and Canada, oversized wire opening. Flat end screw with cut trepan face for gripping large and small stranded wires without damage. 2 legs at .3 x .063 with a .15" penetration. International Hydraulics Inc® brand.

E129884 UL486A,B, ZMVV, ZMVV7, 1243943 Canada 22.2 No.65

Temperature Range and Rating Guide

Body and Staple THT Types

 Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper wire, stranded and solid wire per UL486 wire code. Solid copper bus staple for tens of micro ohms range of copper to copper high conductivity, low resistance current path.  Meets IEC volt drop test standards. Variety of THT leg length to accommodate PCB of various thicknesses including multilayer. 

Dimensions

A: 0.41" (10.4mm)

B: 0.56" (14.2mm)

C: 0.42" (10.7mm)

See Mechanical Drawing for detailed dimensions

*Wire range only valid with use of a bus bar or staple.

"B2A" 2 AWG OEM, 2-14 AWG wire range, tin plated aluminum with steel screw, aluminum or copper wire, CU7AL, 75C temperature rating, single wire terminal, UL Recognized at 600v - acceptable for use through 2000v, Canada Certified. The most compact #2 AWG wire connector available.

Temperature Range and Rating Guide

Screwdriver Bit Information

Please email for higher volume prices

90C (AL9CU) version available.

115 Amps copper alloy bus cross section .25 x .04
or
.25 x .05 or 50 Amps bus 5/32" or

.25 x .032

Dimensions

A: 0.41" (10.4mm)

B: 0.56" (14.2mm)

C: 0.42" (10.7mm)

See Mechanical Drawing for detailed dimensions

*Wire range only valid with use of a bus bar or staple.

"B2A-HEX" 2 AWG OEM, 2-14 AWG wire range, tin plated aluminum with hex socket screw, aluminum or copper wire, CU7AL, 75C temperature rating, single wire terminal, UL Recognized at 600v - acceptable for use through 2000v, Canada Certified. The most compact #2 AWG wire connector available.

Temperature Range and Rating Guide

Please email for higher volume prices

90C (AL9CU) version available.

Dimensions

A: 0.41" (10.4mm)

B: 0.56" (14.2mm)

C: 0.42" (10.7mm)

See Mechanical Drawing for detailed dimensions

B2A-PCB: 2 AWG PCB wire lug, (2)3-14 AWG, 115A/100A AMP, slotted set screw. 2 legs (.24X.05”) with a 0.16" (4mm) PCB penetration. Side wire, and top screw entrance. UL Recognized at 600v - acceptable for use through 2000v. Canada Certified. IHI Connectors® brand.

Temperature Range and Rating Guide

Screwdriver Bit Information

90C (AL9CU) version available.

Body and Staple THT Types

 Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper or aluminum wire, stranded and solid wire per UL486 wire code. Solid copper bus staple for tens of micro ohms range of copper to copper high conductivity, low resistance current path.  Meets IEC volt drop test standards. Variety of THT leg length to accommodate PCB of various thicknesses including multilayer. 

Zinc plated steel screw, and tin plated copper staple, solderable

Dimensions

A: 0.41" (10.4mm)

B: 0.56" (14.2mm)

C: 0.42" (10.7mm)

See Mechanical Drawing for detailed dimensions

B2A-PCB-HEX: 2 AWG PCB wire lug, 2(3)-14 AWG, 115A/100A AMP, HEX socket screw. 2 legs (.24X.05”) with a 0.16" (4mm) PCB penetration. Side wire, and top screw entrance. UL Recognized at 600v - acceptable for use through 2000v. Canada Certified. IHI Connectors® brand.

Temperature Range and Rating Guide

90C (AL9CU) version available.

Body and Staple THT Types

 Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper or aluminum wire, stranded and solid wire per UL486 wire code. Solid copper bus staple for tens of micro ohms range of copper to copper high conductivity, low resistance current path.  Meets IEC volt drop test standards. Variety of THT leg length to accommodate PCB of various thicknesses including multilayer. 

Zinc plated steel screw, and tin plated copper staple, solderable

Dimensions

A: 0.41" (10.4mm)

B: 0.56" (14.2mm)

C: 0.42" (10.7mm)

See Mechanical Drawing for detailed dimensions

B2A-PCB-SS: 2 AWG PCB wire lug, 2(3)-14 AWG, 115A/100A AMP, stainless steel screw. 2 legs (.24X.05”) with a 0.16" (4mm) PCB penetration. Side wire, and top screw entrance. UL Recognized at 600v - acceptable for use through 2000v. Canada Certified. IHI Connectors® brand.

Temperature Range and Rating Guide

Body and Staple THT Types

 Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper or aluminum wire, stranded and solid wire per UL486 wire code. Solid copper bus staple for tens of micro ohms range of copper to copper high conductivity, low resistance current path.  Meets IEC volt drop test standards. Variety of THT leg length to accommodate PCB of various thicknesses including multilayer. Variety of THT leg length to accommodate PCB of various thicknesses including

Stainless steel screw, and tin plated copper staple, solderable

Dimensions

A: 0.41" (10.4mm)

B: 0.56" (14.2mm)

C: 0.42" (10.7mm)

See Mechanical Drawing for detailed dimensions

B2A-NM-PCB-BUSMOUNT-HEX-KIT: 2 AWG PCB wire lug, 2-14 AWG, 115A/100A AMP, short HEX set screw. 2 legs (.24X.05”) with a 0.16" (4mm) PCB penetration.

Temperature Range and Rating Guide

Body and Staple THT Types

 Wave and reflow solderable high current PCB wire terminal lug / connector for high amp power applications. THT (Through Hole Technology). Copper or aluminum wire, stranded and solid wire per UL486 wire code. Solid copper bus staple for tens of micro ohms range of copper to copper high conductivity, low resistance current path.  Meets IEC volt drop test standards.

Black oxide plated steel screw, and tin plated copper staple, solderable

BUS BAR CUSTOMER SUPPLIED